Description

Technical Parameters

Blend300 (Trisester Complex) 300mg/ml Core Introduction

Pharmaceutical -grade injection | Testosterone Acetate + Testosterone Decanoate + Testosterone Propionate (a complete androgen supplement )

Combination formula :

Testosterone Acetate (TRA) : 50mg/ml

Testosterone Decanoate (TD) : 100mg/ml

Testosterone Propionate (TP) : 150mg/ml

Total concentration : 300mg/ml

Solvent : Cottonseed oil/Sesame oil + Benzyl alcohol (2%)

Appearance : Transparent light yellow oily liquid

Core Effects

Blend300 is a three-ester testosterone formulation that delivers the triple benefits of rapid onset, smooth transition, and long-lasting stability through a precise blend of fast-acting, intermediate-acting, and long-acting esters . It is suitable for hormone replacement therapy, muscle-building cycles, and performance optimization .

✅ Three-phase release advantages :

Propionate (TP) : Rapid-release (peaking in 2-4 hours), providing immediate hormonal support

Acetate (TRA) : Intermediate release (1-2 day half-life), smooth transition of blood concentration

Decanoate (TD) : long-lasting sustained release (15-day half-life), maintaining long-term stable effects

✅ Powerful muscle building :

Promote protein synthesis , and increase muscle mass by 8-12kg in 12-16 weeks

Significantly improve strength levels and break through training bottlenecks

✅ Physiological function optimization :

Improve sexual function , enhance libido and erectile function

Enhance red blood cell production and improve oxygen delivery capacity

End Product Preparation Guide

1. Preparation of injection oil (300mg/ml) :

Example recipe (100ml preparation):

Testosterone propionate raw material: 15.0g

Testosterone acetate raw material: 5.0g

Testosterone decanoate raw material: 10.0g

Benzyl alcohol: 2.0ml

Cottonseed oil: add to 100ml

Preparation process :

Raw material pretreatment : micronization (D90≤10μm)

Step -by-step dissolution :

First dissolve testosterone propionate (40°C water bath, magnetic stirring)

Add testosterone acetate and stir until completely dissolved

Finally, add testosterone decanoate and continue stirring.

Oil replenishment and mixing : Add the remaining oil phase and continue stirring for 40 minutes

Sterile Filtration :

Pre-filtration: 1.0μm filter membrane to remove large particles

Final filtration: 0.22μm PES membrane positive pressure filtration

Subpackaging : Subpackaging into sterile injection bottles under aseptic environment

Quality Control :

HPLC assay :

Testosterone propionate: 95-105% labeled amount (142.5-157.5 mg/ml)

Testosterone acetate: 95-105% labeled amount (47.5-52.5 mg/ml)

Testosterone Decanoate: 95-105% labeled amount (95-105 mg/ml)

Endotoxin detection : <0.5EU/ml

Sterility test : 14 days of incubation by membrane filtration

2. Preparation Notes :

Dissolution order : Dissolve in descending order of solubility (propionate → acetate → decanoate)

Temperature control : 40-45°C water bath to avoid high temperature degradation

Stirring speed : 200-300 rpm to ensure complete dissolution

Filtration pressure : positive pressure filtration, pressure ≤ 0.3MPa

Usage Protocol

1. Hormone replacement therapy (TRT) :

Dosage : 150-300 mg every 2 weeks, deep intramuscularly

Treatment duration : Long-term treatment

Monitoring : Regularly check blood testosterone levels and hematocrit

2. Bulking Cycle :

Dosage : 300-600 mg/week, deep intramuscular injection

Duration : 12-16 weeks

Results : Increased lean body mass by 8-12kg and significantly improved strength

3. Injection technique :

Injection route : Deep intramuscular injection

Injection site :

Gluteus maximus : preferred site, stable absorption

Deltoid muscle : Secondary site, easy to operate

Vastus lateralis : optional site, injection required in rotation

Needle Selection :

Gluteal injection : 23G 1.5-inch needle

Deltoid injection : 25G 1-inch needle

Injection frequency : 2 times a week (Monday/Thursday)

4. Injection steps :

Preparation before injection :

Wash your hands and prepare alcohol pads, needles, and syringes

Warm the vial to 37°C (hold in the palm of your hand for 2 minutes)

Drug extraction operation :

Sterilize the rubber stopper and inject an equal amount of air

Slowly draw out the required dose, removing any air bubbles.

Injection procedure :

Disinfect the injection site (5 cm diameter circle)

Rapidly advance the needle 90 degrees and slowly push the needle in (30 seconds/ml)

Press the cotton pad after pulling it out, do not massage the injection site

Lifecycle Support and Management

Mid- cycle support :

Antiestrogens :

Anastrozole 0.5 mg/week (adjusted based on estrogen symptoms)

Tamoxifen 10 mg every other day (to prevent estrogen-induced breast cancer)

Liver support : Silymarin 600mg/day

Cardiovascular protection : Fish oil 3g/day + Coenzyme Q10 200mg/day

PCT Requirements :

Start time : 2 weeks after the last injection (decanoate has a long half-life)

Solution :

Tamoxifen: 20 mg/day for 4 weeks → 10 mg/day for 2 weeks

Clomiphene: 50 mg/day for 2 weeks → 25 mg/day for 2 weeks

Why choose Blend300 ?

Triester complex formula achieves a perfect balance of fast-acting, medium-acting and long-acting

Powerful muscle growth and physiological function optimization , comprehensively improving competitive state

Stable blood drug concentration , avoiding mood and physical fluctuations

Quality Assurance :

GMP compliant production , aseptic filling process

Third-party laboratory testing (triple HPLC assay)

Endotoxin detection (<0.5EU/ml)

Worldwide Shipping :

Medical multi-dose bottle packaging

Private delivery , no logo on the outer packaging

Temperature- stable transportation to ensure product stability

Conclusion

Blend300 is formulated using precise proportions and aseptic processing , making it particularly suitable for hormone replacement therapy, muscle-building cycles, and athletic performance optimization . The recommended dose is 300-600mg/week .

Need a specific usage plan ?

We provide professional medication guidance to help you achieve your goals safely and efficiently!

Need anything, please contact us